Dog Shock Collar, PEACHAR Dog Training Collar with 2300Ft Remote, Electric Shock Collar with Beep Vibration Shock and Security Lock Mode Waterproof Rechargeable Shock Collar for Small Large Medium Dog

Help your pup mind their manners with the Remote Dog Training Electric Collar.

Train your pup to be on his best behavior with the PEACHAR X100 Waterproof Remote Dog Training Collar. This training collar lets you choose between three types of stimulation—sound, vibration and static. With multiple signal strengths, you can start with a mild correction and see which option your dog responds to best.

Suitable different size dogs

The size of the dog training collar is adjustable, you can change the size of it according your dog"s size, no need to worry about the unfit for your dog.

Upgrade Four Training Modes

This dog training collar offers four adjustable training modes: beep (indicator light is green), vibration ( level 1-9) (indicator light is green)and shock (level 1-99 ) (indicator light is red ) and shock boost (10% higher)(indicator light is red )

Waterproof

The collar is waterproof that the dogs can run and walks in rain.

Long Standby Rechargeable Battery

This collar uses a rechargeable lithium battery.

Keyboard Lock function

With screen lock function, it can avoid triggering by mistake and causing alarm to the dog

With upgraded conductive silicone cover, the prongs can provide double protection and prevent your dog"s skin from irration.

Select a pair of short or long metal probes according to the thickness of pet hair and install them on the receiver

What if the dog doesn"t respond when the shock button is pressed?

1. When you press the shock button, please check whether the indicator light on the receiver and remote control is red

2. Please make sure that two metal prongs touch the dog"s skin directly at the same time.

3. please remove the two conductive silicone prong covers to try, conductive silicone prong can weaken electric shock.

The transmitter and receiver are equipped with a rechargeable battery.

The recharge time is 1.5-2 hours to full battery recharge. The receiver will then remain in standby mode for 15 days, the transmitter for up to 180 days depending on use.

Note：The remote control has a power saving mode. When the remote control is not operated for more than 3 minutes, the screen will turn off and you can activate the screen by pressing any button(The switch knob cannot activate the screen directly in this situation).

When charging the receiver:

it lights up red when plugged in and will intermittently flash green, (green is the signal light)

After about 2 hours, it will turn green, indicating that the receiver is fully charged.

When charging the remote:

it lights up red when charging.

After about 2 hours, it will turn green, indicating that the remote is fully charged.

Question: Both the receiver and the remote control are fully charged, but the receiver does not respond when the remote control is pressed. What happeded?

Answer: 1. Make sure the receiver is turned on.

2. Please check if the remote is switched to the "CH1".

3. if it still doesn"t work, You need to re-pair.

Friendly Tips

1. Check the tightness off the collar by inserting one or two finger snugly between the collar and neck.

2.If you don"t need the shock function, you can remove the metal probes, so that wearing the shock collar is more comfortable for your dog. If you use, please make sure the two conductive points have contacted with dog"s skin on the underside of neck directly at the same time.

3.Avoid leaving the receiver on the dog for more than 12 hours per day. or it may cause skin irritation. Keep checking the dog"s skin condition every day.

4.Four channels to support training 4 dogs simultaneously with the purchase of additional collars.

5.Our factory setting is paired with channel 1. The collar"s battery will be displayed on the remote screen for channel 1.

For other channels, if you need, you can pair by yourself.

6. Note：The remote control has a power saving mode. When the remote control is not operated for more than 3 minutes, the screen will turn off and you can activate the screen by pressing any button(The switch knob cannot activate the screen directly in this situation).

FAQs

Q1: when the unit was turned on the screen would go off. Turning it back on and off would NOT fix this. What should I do?

A1: The remote control has a power saving mode. When the remote control is not operated for more than 3 minutes, the screen will turn off and you can activate the screen by pressing any button(The switch knob cannot activate the screen directly in this situation).

Q2：The receiver is fully charged, but the control shows that the receiver has no power. What happened？

A2：Our factory setting is the receiver corresponds to the ”CH1 “on the remote control

You need to adjust the CH to dog1, then the battery display is normal. if the problem still exist, you need to re-pair the remote and the receiver.

Q3：How to re-pair the remote and the receiver?

A3. 1. make sure the receiver is turned off.

2.Turn on the remote control.

3. Press "CH" button on the right side of the remote control to select the channel you want to pair.

Then press and hold the "CH" button until the green light flashes.

4. press and hold the on/off button of the receiver for about 6S Immediately, you will hear a beep and the green light will flash.

Then you can see the power display of the receiver on the screen of the remote control, indicating that the pairing is successful.